aussie intake - FirebirdV6.com/CamaroV6.com Message Board

Announcement

Collapse
No announcement yet.

aussie intake

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #31
    Looks great! When are you planning to install it? And, how much are you able to safely port that lower out?

    2002 SOM Z28 Camaro - 12.9 @ 104 mph
    1996 3800 Camaro - 13.43 @ 100.77 mph


    Project Cars | How To Guides | Scratch Repair | Synthetic Oil

    Comment


    • #32
      the install's gonna be a ways off. Im planning on pulling the engine and tranny for a full rebuild with flat top pistons, cam and intense heads. Getting the time for this between work and taking care of my kid is sketchy at best. As far as porting goes, im gonna gasket match the ports at the head surface. the runners and plenum im just going to mirror polish the inside. I want air velocity more than air flow for this build, so I don't want to open up the runners too much, just make then smooth as glass so theres no restriction in the air path.

      Comment


      • #33
        So I removed the stock manifold to fit the aussie one. As you can see from the pics the manifold fits in the car without any modification. The problem is the huge dbw f-body throttle body. In any position it hits the underside of the cowl and is about an inch too low for the throttle bore to line up with the plenum inlet. So doesn't look like I can avoid cutting the cowl.
        Attached Files

        Comment


        • #34
          Well that sucks, but it does look pretty cool in there. How much of the cowl needs to go so you can fit the TB?
          08' L76 6.0L 4X4 Chevy EXT.Cab LTZ Vortec MAX with Snug top cover, Dynomax exhaust,Hptuners& K&N intake
          96' Camaro M5 to A4 conversion, alot of mods . GT35R Turbo full suspension. Built engine

          Comment


          • #35
            Originally posted by mdiesel View Post
            So I removed the stock manifold to fit the aussie one. As you can see from the pics the manifold fits in the car without any modification. The problem is the huge dbw f-body throttle body. In any position it hits the underside of the cowl and is about an inch too low for the throttle bore to line up with the plenum inlet. So doesn't look like I can avoid cutting the cowl.
            Nice! We had another member that ran into some similar troubles as well here: Camaro Holden Intake build

            I believe he talked about lowering the motor a little bit with a spacer somewhere in that thread if I am not mistaken

            2002 SOM Z28 Camaro - 12.9 @ 104 mph
            1996 3800 Camaro - 13.43 @ 100.77 mph


            Project Cars | How To Guides | Scratch Repair | Synthetic Oil

            Comment


            • #36
              I found this on ebay austrailia, it'll bolt right up to the manifold, turn the throttle forwards, im hoping it'll get it forwards enough to get the TB just past the front lip of the cowl. I have a cowl induction hood, so once its past that cowl lip hood clearance isn't an issue. if this works my woes are solved.
              Attached Files

              Comment


              • #37
                So I got the aussie elbow today. Itll work perfectly. Just gotta fab up a 1/4" thick flat adapter for the two bolt patterns, but it'll allow me to mount the throttle body without any modification to the cowl, manifold, or tb.
                Attached Files

                Comment


                • #38
                  Nice, looking good..
                  08' L76 6.0L 4X4 Chevy EXT.Cab LTZ Vortec MAX with Snug top cover, Dynomax exhaust,Hptuners& K&N intake
                  96' Camaro M5 to A4 conversion, alot of mods . GT35R Turbo full suspension. Built engine

                  Comment


                  • #39
                    Got the adapter plate for the throttle fabed up. Now that the fitment issue is solved I can get back on porting the intake... more updates to come
                    Attached Files

                    Comment


                    • #40
                      Looks great.
                      08' L76 6.0L 4X4 Chevy EXT.Cab LTZ Vortec MAX with Snug top cover, Dynomax exhaust,Hptuners& K&N intake
                      96' Camaro M5 to A4 conversion, alot of mods . GT35R Turbo full suspension. Built engine

                      Comment


                      • #41
                        A few more pics of the fitment now that the throttle adapter is done...
                        Attached Files

                        Comment


                        • #42
                          Looks clean! How much longer until she's running?

                          2002 SOM Z28 Camaro - 12.9 @ 104 mph
                          1996 3800 Camaro - 13.43 @ 100.77 mph


                          Project Cars | How To Guides | Scratch Repair | Synthetic Oil

                          Comment


                          • #43
                            I still have to figure out how to convince the wife why I need to spend more money on the car, lol

                            Comment


                            • #44
                              no new pics for today, but after much trial and error it seams no combination of fittings will allow me to make the connection from the manifold to the belt tensioner for the heater core . I could order an aussie tensioner, upper and lower heat pipes ( yea theirs are separate from the tensioner ) but none of the ebay junkyards have all the parts from one place so id have to pay 3 times shipping. so, Im just gonna plug the openings at the manifold and water pump and delete the heater core all together. I figure I live in Florida I don't need heat... especially on a car that im only gonna be driving for fun on weekends.

                              Comment


                              • #45
                                Yeah, no need for heat, I won’t have heat or A/C when the turbo goes on.
                                08' L76 6.0L 4X4 Chevy EXT.Cab LTZ Vortec MAX with Snug top cover, Dynomax exhaust,Hptuners& K&N intake
                                96' Camaro M5 to A4 conversion, alot of mods . GT35R Turbo full suspension. Built engine

                                Comment

                                Latest Topics

                                Collapse

                                There are no results that meet this criteria.

                                FORUM SPONSORS

                                Collapse
                                Working...
                                X