The Official 2016-Present V6 Camaro Exhaust Thread

[LETZRIDE]

2019 V6 Camaro RS Borla Atak

[LETZRIDE]

So I’ve been having an issue and I hope you guys can help. I own a 2019 V6 camaro LT and I’ve done quite a lot to it. It has a secondary cat delete, resonator delete, borla atak axle back and everything has been great so far. I just recently installed ARH catted downpipe and the sound got even better BUT whenever I’m coasting or let my foot off the pedal, it causes my muffler to give off an obnoxious rattle. Took it to 2 shops and they just say “it’s because you have a v6” -_- any suggestions to fix this? I was thinking put a muffler where I straight piped my resonator?

Hey Jules, I created a new thread for you to help address this question as this thread is for exhaust sound clips. The thread I made for you is titled "2019 Camaro Exhaust Rattle"

I put my suggestions in there so we can keep this thread clean.

Thanks and welcome to the site!

[Jules_v6]

So I’ve been having an issue and I hope you guys can help. I own a 2019 V6 camaro LT and I’ve done quite a lot to it. It has a secondary cat delete, resonator delete, borla atak axle back and everything has been great so far. I just recently installed ARH catted downpipe and the sound got even better BUT whenever I’m coasting or let my foot off the pedal, it causes my muffler to give off an obnoxious rattle. Took it to 2 shops and they just say “it’s because you have a v6” -_- any suggestions to fix this? I was thinking put a muffler where I straight piped my resonator?

[LETZRIDE]

where did you buy the headers? Ive been looking for headers for my 19 RS for a little bit and haven't had any luck.

You won’t find headers for your car as they won’t exist. You have the LGX motor which is setup similar the LFX which has the header designed into the cylinder head and comes out as one single port. Since it is built into your cylinder head you cannot change it.

This short video shows why as well:

https://m.youtube.com/watch?v=D2Gd2I...e_continue=111

[Fitwithg]

So far, dual ram intakes running through the foglights, catless BBK longtube headers ported to match the gasket on the exhaust manifold, going into three inch oval t304 stainless steel pipes exiting on the sides of the car. So far, no crosspipe, will be adding that when I put on the porter mufflers that just came in. Going to try and use the oval pipe that gets cut off for that. Also has a full cradle swap, rocking 3.45 gears, have 4.10s on the dresser waiting to be put it. Haven't gotten around to that yet

where did you buy the headers? Ive been looking for headers for my 19 RS for a little bit and haven't had any luck.

[versionx]

Sounds good what mods ?

I only have a Magnaflow Axle Back Race Series exhaust. I'm thinking of deleting the secondary cats next.

[ssms5411]

Sounds good what mods ?

[versionx]

Here is mine :)

https://www.youtube.com/watch?v=PfqSteMG3rY

[ssms5411]

Nice.

[LETZRIDE]

https://youtu.be/eTxDG_q9V0E

Nice sound!

[Mannyphx]

https://youtu.be/eTxDG_q9V0E

[LETZRIDE]

2011. I made a post in the fifth gen thread a few minutes ago, must have clicked on the wrong one

no worries - I'll clean the thread up and delete the posts in here to keep this thread clean

[LETZRIDE]

2016 Camaro V6 Stock to Borla Atak Exhaust

2017 V6 Camaro - muffler delete

6th Gen V6 Camaro - Flowmaster American Thunder Axle-back Exhaust System

[SidepipesMcGee]

2011. I made a post in the fifth gen thread a few minutes ago, must have clicked on the wrong one

[LETZRIDE]

2016 V6 Camaro muffler delete

6th Gen V6 Camaro - Borla S-type Axle Back Exhaust

2016 V6 Camaro MRT V2 Axle Back Exhaust